Newest Products
Z60-23 Burnishing Ring 4-1/2"
This 4-1/2", medium burnishing wheel was made to fill the gap between the Z60-3A and Z60-3B, supplied standard with the Z60 machine. Also Available:N95 3-1/2" Dent Removing RingN95B 4-1/2" Dent...
Z60-24 1-1/4" Power Disc
This was the 4th Power Disc in the series, it was designed specifically for doing saxophone bell rims of alto, tenor and baritones, usually without removing the bell, saving time....
Z60-25AL Low Profile Power Disc
Smaller than the Z60-25 this special low profile Power Disc is for old style cornets and piccolo trumpets. Also, orchestral pitches, D, Eb, etc. 2-1/2 low profile power disc.
Z60-25L Low Profile 3" Disc
Same size as the Z60-25, but low profile for marching units. Note: These low profile units are NOT meant to replace the regular power discs on a daily basis. They...
Z60-25 3" Power Disc
One of the first 3 Power Disc designs; this one is for cornets, trumpets and other bells up to about 6 in diameter. 3" power disc.
Z60-26 4" Power Disc
Again, one of the first 3, this size is for bells over 6" in diameter, like trombone, baritone/euphonium, French horn, small tuba and sousaphone. 4" Power Disc.
Z60-26L Low Profile 4" Disc
Same size as Z60-26, but low profile for larger marching units. Note: These low profile units are NOT meant to replace the regular power discs on a daily basis. They...
Z60-27 5" Power Disc
Last of the first 3, this one is almost exclusively for the outer 4 of an old style wide flared tuba and most sousaphones. Once you are 4 or so...
Z60-28 5" Roller
This 5" roller gives full support for rolling larger diameter bells for trombone and larger, especially helpful for French horn bells which are thinner and need the support. Helps avoid...
Z60-29 Tapered Slim Roller
This tapered slim roller creates a work area inside the small cornet and trumpet sized bells for the same reasons noted in Z60-28.
Z60-30 Convex Roller
The convex roller was designed for use with all saxophone bell flares, you will see the work patterns develop in 3 different areas.
Z60-32 30 Degree Arm
Imagine, if you will, the machine thrown over your shoulder like a set of bagpipes, so that you can better attend to the matters at hand. No more interference of...
Z60-33 7" Roller
The new Z60-33, 7 Inch Roller was developed for tubas and provides that extra measure of security that you need when you have an uneven distribution of weight most large...
Z60-36A Small Trumpet Stem Roller
This double radii roller was the first step in addressing the cornet and trumpet bell stem tubing. Does both sides of the bow. ALSO AVAILABLE: DOUBLE RADII ROLLERS Z60-36B LARGE...
Z60-36B Large Trumpet Stem Roller
This double radii roller was a continuum for cornet and trumpet bells and also a new world for the trombone work they fit. Does from the tuning slide to the...
Z60-36 1-1/4 Curved Roller
This roller was necessary to properly utilize the Z61-11 Articulated Tuba Rod by allowing you to go under the tubing for complete 360 degree coverage of the outside diameter of the...
Z60-38 & 39 Flute Mandrels for the Z60 Dent Machine
Z60-38 Flute Head Mandrel This is a flute head joint mandrel for the Z60-14 Straight Mandrel, similar to the N75 Flute Head Mandrel. Use with Z60-36A Roller or the P1 Precision...
Z60-3A/3B-Circular Burnishing Wheels
These burnishing wheels are also included standard with the Z60 Dent Machine. Great for Baritone Saxophones bells, Euphonium bells, Tuba Bells, or any large bell brass throat where you need...