Newest Products
N63A Larger Barrel Type Dent Balls
The larger sets listed below greatly increase your work range. The regular sets increase in .025 (.635mm) steps. The half size sets allow for much finer work if used with...
N63B Larger Barrel Type Dent Balls(Half Sizes)
The larger sets listed below greatly increase your work range. The regular sets increase in .025 (.635mm) steps. The half size sets allow for much finer work if used with...
N64A Larger Barrel Type Dent Balls
The larger sets listed below greatly increase your work range. The regular sets increase in .025 (.635mm) steps. The half size sets allow for much finer work if used with...
N64B Larger Barrel Type Dent Balls(Half Sizes)
The larger sets listed below greatly increase your work range. The regular sets increase in .025 (.635mm) steps. The half size sets allow for much finer work if used with...
N65 Barrel Shaped Dent Ball Set
A set of 10 barrel shaped dent balls are threaded with 1/2-13 threads. To fit any Ferree dent rod that will hold the N80D or E round dent balls.These rods...
N66 Mouthpiece Receiver Reamers
Ferree's makes FOUR sizes of mouthpiece receiver reamers. Use where the mouthpipe is expanded inside a ferrule, instead of having a separate machined receiver to clean up bore. N66A Mouthpiece...
N67 3ft (.91m) Curved Dent Rod
A 3ft (.91m) curved, 5/8 (15.9mm) DIA. rod for baritones, basses. Uses N80DS and N80ES sets of balls.
N68 Right Angle Dent Rod
This rod is used to remove dents from mouth pipes. Especially for Conn 14A & 15A cornets which have tuning slides set up like a trumpet or any other instrument...
N69 5ft (1.52m) Curve Dent Rod
A 5ft (1.52m) curve, 3/4 (19.0mm) diameter rod for baritones, sousaphones and recording basses. Uses N80DS and N80ES sets of balls. Cannot ship by regular mail.
N70 French Horn Dent Rod 1/2 (12.7mm), 3ft (.91mm)
This French Horn Dent Rod measures 3ft (.91mm) with a 1/2 (12.7mm) diameter for French horns, threaded on both ends to receive N80CS set of balls. Curved on one end,...
N71 French Horn Dent Rod 1/2 (12.7mm), 3ft (.91mm) Curved
This French Horn Dent Rod measures 1/2 (12.7mm), 3ft (.91mm) curved on both ends. Made from stress proof steel for French horns and mellophones. This rod is threaded on both...
N72 Body Bow Dent Remover
A double ended, curved and tapered rod, 18 (457mm) long and 1/2 (12.7mm) in diameter. Intended to remove dents in the sax body bow by inserting balls through the Eb...
N73 Sax Gooseneck Dent Rod
This Sax Gooseneck Dent Rod has a 1/2 (12.7mm) tapered and curved rod was designed to help remove dents from all sax goosenecks using the fast, rod and ball technique....
N74 4ft (1.22m) Straight Dent Rod
N74 4ft (1.22m) straight, 3/4 (19mm) threaded on one end for N80D and N80E balls for sax bells, baritones and sousaphones tapered and threaded on the other end for use...
N75 Flute Head Mandrels
Designed to fit the taper of flute heads. Works like a tapered mandrel as used on cornet bells. Useful in removing dents and rounding out egg shaped joints. N75 Flute...
N76 Flute Body Mandrels
Straight mandrels designed to be useful in removing dents and straightening flute bodies. N76 Flute Body Mandrel for soprano flutes.734 (18.6mm) N76A Flute Body Mandrel for alto flutes .937 (23.8mm)...
N77 Head Swedging Dies
Ferrees Flute and Piccolo Head Swedging Dies were designed to shrink the tenons that have been over expanded. These dies can also be used to remove ridges and dents from...
N78 Flute Pad Cup Tools
The set consists of two arbors with a different diameter on each end, making 4 sizes to work with. They were designed for two purposes. First, to straighten bowed pad...
N79 Flute Pad Hole Punch Set
The N79 set is designed to punch larger holes in standard flute pads for use on open hole French type flutes, so that Repairmen need not carry two complete flute...
N79Y Yamaha Flute Pad Punch
The special N79Y (6mm dia.) optional punch, is used to en-large the hole in some flute pads having too small a hole to fit in Yamaha flutes with their raised...