Newest Products
N17 Bassoon Bocal Cable
A tool to make bassoon dent work easier. The cable has a threaded connection in the middle that allows it to be split into two pieces. This permits putting a...
N19 Soldering Clamp
This clamp is designed to be used with the largest tubas as well as small instruments. Its distinguishing features include a threaded shaft that is long enough to eliminate the...
N20-24 Valve Lapping Blocks
Used for lapping-in newly replaced or repaired valves.N20 Cornet/Trumpet, 5/8 (14.9mm)N21 Small Baritone, 11/16 (17.5mm)N22 Large Baritone, 3/4 (19mm)N23 Small Bass, 15/16 (23.8mm)N24 Large Bass, 1-1/16 (27mm) N25 Tuba 1...
N28 GROUND VALVE SLEEVE SET
6 OR 10 PC SET OF N28 GROUND VALVE SLEEVES AT A HUGE SAVINGS OVER INDIVIDUAL PRICES ** Put the sizes you want in the note section of your order...
N28A Ground Valve Sleeve .631-.700"
These steel sleeves have a standard length of 3" and are used to straighten bent and out of round pistons. The sleeves have been bored and then honed to the...
N28C Ground Valve Casing .701-.885"
These steel sleeves have a standard length of 3" and are used to straighten bent and out of round pistons. The sleeves have been bored and then honed to the...
N28D Ground Valve Sleeve .886-1.400"
These steel sleeves have a standard length of 3" and are used to straighten bent and out of round pistons. The sleeves have been bored and then honed to the...
N29S Special Dent Ball Set
These specially produced balls are not a typical spherical or barrel type ball. These are for odd places you are sometimes faced with. Some are egg shaped, some are semi-elliptical,...
N2A Wood Burnisher Handle
N2A Wood Handle for burnishers listed below. STRAIGHT BURNISHERS N1 Straight Burnisher, small 6" (152.4mm) N2 Straight Burnisher, standard 8" (203mm) N3 Straight Burnisher, large 10" (254mm) HOOK BURNISHER N105...
N30 Sousa Bell Jack
Adjustable to straighten sousaphone bell tenons, especially on fiberglass sousaphones which bend even easier.
N31 3ft (.91mm) straight, 5/8" (15.9mm) rod
N31 3ft (.91m) straight, 5/8 (15.9mm) rod for use on baritones, sousaphones and with the N81 sax dent balls. Also uses N80CS, N80DS and N80ES balls. N31A 3ft (.91m) straight,...
N32 2ft (61cm) curve, 5/8 (15.9mm) rod
N32 2ft (61cm) curve, 5/8 (15.9mm) rod for use on saxophones, baritones and sousaphones. Uses N80CS, N80DS and N80ES balls.
N33 4ft (1.22m) ends curved, 3/4 ( 19mm) rod
N33 4 ft (1.22m) small ends curved, 3/4" (19mm) rod for saxophones, baritones and sousaphones. Uses N80CS, N80D and N80E balls.
N34 3-1/2 FT (1.07m), 3/4 (19mm) diameter curve rod
Reaches extra far into sousaphones. Â Threaded for N80DS and N80ES balls. Has a plate on one end to help prevents slipping under heavy pressure.
N35 - N35A Right Angle Expandable Dent Tool
This Right Angle Expandable Dent Tool is made with 2 diameters N35- 7/16" (11.1mm) and the N35A- .468 (11.89mm). You can use these tools on Cornets, Trumpets, French horns and some...
N4 Yamaha Tuning Slide Dent Removal Kit
If you service Yamaha cornets or trumpets this tuning slide dent removal kit is a must have addition to the shop. Because of the manufacturing process (silver soldered draw knob),...
N40-N42-N44-N46 Expandable Slide Dent Tools
Expandable Slide Dent Tools N40 Small Expandable Sousa Dent Tool5/8"(15.87mm)...